BSEE, BSET and BSCS students can use this guide to study Tony R. Kuphaldt’s “Lessons in Electric Circuits, Volume I: DC”. It is a plain-spoken first text on DC circuit analysis and the basics of electricity, and it is also a friendly entry point for students who are new to electronics. The author’s current edition is published under the Creative Commons Attribution licence (CC BY 4.0), so you can read, share and adapt it with credit.
The book starts with static electricity, conductors and Ohm’s law, then builds up through electrical safety, series and parallel circuits, Kirchhoff’s laws and DC metering to full network analysis with the Thevenin, Norton and superposition theorems. The last chapters cover batteries, wire and fuses, capacitors, magnetism, inductors and RC and L/R time constants. SPICE listings and worked examples run through every chapter, so it suits first-semester study as well as revision before a circuits paper.
Book Overview
| Course | Circuit Analysis (DC) / Basic Electrical Circuits |
| Degree Programs | BSEE, BSCS, BSET |
| Level | University / Undergraduate (also an entry text for beginners) |
| Edition | Fifth Edition, last revised October 18, 2006 (minor revision February 3, 2023) |
| Author | Tony R. Kuphaldt |
| Source | Author’s site (ibiblio); web edition on All About Circuits |
| Total Chapters | 16 chapters, plus 3 appendices |
| Exercises | Worked examples and review lists in the chapters; no end-of-chapter problem sets |
| Language | English |
| License | Creative Commons Attribution 4.0 International (CC BY 4.0) |
| Format | PDF, HTML and PostScript |
Chapter List
Chapter 1: Basic Concepts of Electricity
Difficulty: Easy · Key topics: static electricity, atoms, free electrons, conductors and insulators, circuits, voltage, current, resistance, electron flow
The chapter starts with static electricity: glass rubbed with silk and wax rubbed with wool attract and repel, which leads to the atom and its electrons, protons and neutrons. It then separates conductors, with loosely held free electrons, from insulators, and shows why continuous current needs a complete loop, a circuit. Voltage is introduced as potential energy per unit charge between two points, current as the flow of electrons, and resistance as opposition to that flow, using a lamp circuit. The chapter ends with short, open and closed circuits and the old argument between conventional flow and electron flow.
Key Points:
- Electrons carry negative charge, protons positive charge and neutrons none; the number of protons fixes the element.
- All metals are conductors because their outer electrons are free; insulators hold their electrons tightly.
- A circuit is an unbroken loop, and a break anywhere in it stops current everywhere in it.
- Voltage is potential energy per unit charge between two points; in a one-loop circuit the current is the same at every point.
- One coulomb is about 6.25 x 1018 electrons.
- A short circuit has almost no resistance and can release dangerous heat; an open circuit has a break in its path.
- Conventional flow comes from Franklin’s guess and runs opposite to electron flow; the book draws its circuits with electron flow.
Memory Tip: Picture a hula-hoop full of marbles: push one marble and the whole ring moves, but cut the hoop anywhere and nothing moves.
Common Mistake: Thinking current is “used up” as it goes round a loop. In a simple circuit the current is the same everywhere; it is the voltage that is dropped across each resistance.
Important Questions:
- What is the difference between voltage and current? Voltage is the push, the potential energy per unit charge between two points; current is the flow of electrons that this push causes through a closed path.
- Why does a break anywhere in a circuit stop the current in the whole circuit? Electrons can only flow continuously round a complete loop, so one break stops the flow everywhere, and the full source voltage then appears across the break.
Chapter 2: Ohm’s Law
Difficulty: Easy · Key topics: E = IR, power, Joule’s law, resistors, linear and nonlinear conduction, electrically common points, voltage polarity, SPICE
This chapter gives the central equation of the book. Voltage, current and resistance are tied together by E = IR, and a water-and-pipe analogy of pump pressure, flow and restriction makes the three-way relationship easy to picture. Power is defined as the rate of doing work, with P = IE and the Joule’s law forms P = I2R and P = E2/R. The chapter then describes real resistors and their power ratings, shows where Ohm’s law stops being a straight line (varistors and negative resistance), explains why wires join points that are electrically common, and introduces the polarity of voltage drops and SPICE circuit simulation.
Key Points:
- Ohm’s law has three forms: E = IR, I = E/R and R = E/I, with volts, amps and ohms.
- Electrical power is in watts: P = IE, P = I2R and P = E2/R; one horsepower equals 745.7 watts.
- A resistor has two ratings, ohms and watts; a physically larger resistor can dissipate more heat, but its size does not tell you its resistance.
- For constant resistance a plot of current against voltage is a straight line (linear); a varistor or a tunnel diode gives a curve instead.
- Connecting wires are taken as zero resistance, so points joined by wire are electrically common and have zero volts between them.
- Across a resistor the voltage polarity is negative where electrons enter and positive where they leave.
Practice Tip: Install any free SPICE simulator, simulate one battery and one resistor, and then change the resistor value; the printed current should always follow I = E/R.
Common Mistake: Treating Ohm’s law as true for every component. It describes resistance that stays constant, so it cannot be applied blindly to a varistor or a diode.
Important Questions:
- A 12 V battery drives a 4 Ω heater. What are the current and the power? I = E/R = 12/4 = 3 A, and P = IE = 3 x 12 = 36 W.
- Why can a bigger resistor of the same value handle more power? A larger body has more surface to lose heat, so its watt rating is higher; the ohm value, however, cannot be judged from the size.
Chapter 3: Electrical Safety
Difficulty: Easy · Key topics: shock current, tetanus, fibrillation, ground fault, body resistance, zero energy state, lock-out and tag-out, GFCI, safe meter use
The chapter opens with why safety matters, then explains what current does to the body: deep burns, muscle tetanus that can freeze a hand on a conductor, and disruption of the heart’s rhythm. It shows that a shock needs a path between two points, how grounded power systems make the earth part of that path, and uses Ohm’s law again to show that current, not voltage alone, does the harm and that wet skin has far lower resistance. The rest covers safe practice: the zero energy state, lock-out and tag-out, emergency response, common hazards, safe circuit design with polarized plugs, double insulation and GFCIs, and safe multimeter use.
Key Points:
- Harm depends on the amount of shock current; higher voltage can drive higher current, and high resistance protects.
- DC is more likely to cause tetanus (a victim who cannot let go), while AC is more likely to cause heart fibrillation.
- Shock needs contact between two points of a circuit, and the earth can complete that path through a ground fault.
- Voltages above about 30 are generally treated as able to deliver dangerous current, and wet conditions lower skin resistance.
- When a live circuit must be touched, use one hand only so that no hand-to-hand path crosses the chest.
- Secure a zero energy state, apply lock-out and tag-out, and prove it dead with a meter that you test before and after.
- A GFCI opens the circuit when the currents in the two supply conductors differ, which means current is leaking elsewhere.
Memory Tip: Lock it, tag it, test it, and then touch it first with the back of your hand.
Common Mistake: Assuming low voltage is always safe. A startled jerk can throw you against something more dangerous, and metal jewelry can burn the skin even at low voltage.
Important Questions:
- How does a GFCI protect a person? It compares the current in the two conductors feeding a load; any difference means current is entering or leaving by another route, such as through a person, so it opens a switch and cuts the power.
- What is the first step for a person being shocked? Disconnect them from the source by turning off the switch or breaker, or pull them clear with a dry insulating object; then check breathing and pulse and give CPR if needed.
Chapter 4: Scientific Notation and Metric Prefixes
Difficulty: Easy · Key topics: scientific notation, significant digits, exponents, metric prefixes, prefix conversion, calculator EE key, SPICE notation
This short toolkit chapter shows how to handle the very large and very small numbers of electronics. Scientific notation writes a quantity as significant digits times a power of ten, so multiplying or dividing means multiplying or dividing the digits and then adding or subtracting the exponents. Metric prefixes replace the powers of ten with letters, and a prefix number line from tera to pico shows which way to move the decimal point when converting. The chapter ends with entering exponents on a hand calculator, using the EE key and the scientific and engineering display modes, and with how SPICE prints and reads this notation.
Key Points:
- In scientific notation 4700 is written 4.7 x 103; significant digits show how accurate a number really is.
- To multiply, multiply the digits and add the exponents; to divide, divide the digits and subtract the exponents.
- The prefixes are tera 1012, giga 109, mega 106, kilo 103, milli 10-3, micro 10-6, nano 10-9 and pico 10-12.
- To change prefix, move the decimal point along the prefix number line, one place for each power of ten.
- A number written with no visible decimal point has an implied one to the right of its last digit.
- On a calculator the EE (or E) key enters the power of ten, so you do not type the x 10 yourself.
Memory Tip: Learn the prefix line as steps of three zeros, from tera down to pico, and always read it from large on the left to small on the right.
Common Mistake: Mixing up a small m (milli, 10-3) with a capital M (mega, 106); they differ by a factor of a billion.
Important Questions:
- Express 4700 Ω in kilo-ohms and in scientific notation. 4.7 kΩ, which is 4.7 x 103 Ω.
- What is (3 x 104) multiplied by (2 x 10-6)? Multiply the digits (3 x 2 = 6) and add the exponents (4 + -6 = -2), giving 6 x 10-2, which is 0.06.
Chapter 5: Series and Parallel Circuits
Difficulty: Medium · Key topics: series, parallel, branch, conductance, power, voltage-current-resistance table, open and shorted faults, breadboards
The chapter defines the two basic ways to connect components. In a series circuit there is one path, so current is the same everywhere, resistances add and the voltage drops add up to the source. In a parallel circuit there are exactly two sets of common points, so voltage is the same across every branch, branch currents add and total resistance is smaller than any branch. Conductance (G = 1/R, in siemens) explains the odd-looking parallel formula, and the table method keeps the work tidy. The chapter also covers open and shorted component faults and building circuits on breadboards, soldered boards, wire-wrap and terminal strips.
Key Points:
- Series: the same current in every part, Rtotal = R1 + R2 + … and Etotal = E1 + E2 + …
- Parallel: the same voltage across every branch, 1/Rtotal = 1/R1 + 1/R2 + … and Itotal = I1 + I2 + …
- Conductance G = 1/R is measured in siemens (formerly mhos), and parallel conductances simply add.
- Power is additive in any arrangement: Ptotal = P1 + P2 + … for series, parallel or mixed circuits.
- Use Ohm’s law down one column of the table (the E, I and R of the same part) and the series or parallel rules across a row.
- A shorted component has dramatically lower resistance and an open one dramatically higher; resistors tend to fail open more often than shorted.
Practice Tip: Build a three-resistor series circuit on a breadboard, measure the voltage across each resistor, and check that the three readings add up to the battery voltage.
Common Mistake: Mixing contexts in Ohm’s law, for example dividing the voltage across a group of resistors by the current through just one of them. The values must belong to the same two points.
Important Questions:
- Three resistors of 100, 200 and 300 Ω are in series across 12 V. What is the current? Rtotal = 600 Ω, so I = 12/600 = 20 mA, and the same 20 mA flows through all three.
- Why is the total resistance of parallel resistors smaller than the smallest branch? Every extra branch gives the current another path, so the conductances add; for example 6 kΩ in parallel with 3 kΩ gives 2 kΩ.
Chapter 6: Divider Circuits and Kirchhoff’s Laws
Difficulty: Medium · Key topics: voltage divider, potentiometer, Kirchhoff’s Voltage Law, polarity notation, current divider, Kirchhoff’s Current Law, nodes and loops
Series circuits divide voltage and parallel circuits divide current, and this chapter turns both facts into formulas. The voltage divider shows that each drop is the supply times that resistor’s share of the total resistance, and the potentiometer appears as an adjustable divider. Kirchhoff’s Voltage Law says the voltages around any loop sum to zero, and the chapter teaches the double-subscript voltage notation and how to apply the law to loops, even loops that are not real current paths. The current divider gives each branch its share of the total current, and Kirchhoff’s Current Law says the currents at a node sum to zero.
Key Points:
- Voltage divider: ERn = Etotal x (Rn / Rtotal), so the largest resistor takes the largest drop.
- Current divider: In = Itotal x (Rtotal / Rn), so the smallest resistor takes the largest current.
- KVL: the algebraic sum of all voltages around any closed loop is zero.
- KCL: the algebraic sum of the currents entering and leaving a node is zero.
- A potentiometer has three terminals and works as an adjustable voltage divider.
- A double subscript such as E2-1 means the voltage at point 2 measured with respect to point 1, so the order matters.
Memory Tip: In a series circuit a big resistor takes a big voltage; in a parallel circuit a small resistor takes a big current.
Common Mistake: Dropping the signs in a KVL loop. Walk round the loop in one direction and give every voltage rise and drop its correct sign, or the sum will not come to zero.
Important Questions:
- A 1 kΩ and a 3 kΩ resistor are in series across 12 V. What is the voltage across the 3 kΩ? E = 12 x 3/(1 + 3) = 9 V, and the 1 kΩ resistor drops the other 3 V.
- A total of 6 mA enters a parallel pair of 1 kΩ and 2 kΩ. How does it split? The parallel resistance is 2/3 kΩ, so the 1 kΩ branch takes 6 x (2/3) / 1 = 4 mA and the 2 kΩ branch takes 2 mA, and the two add back to 6 mA as KCL requires.
Chapter 7: Series-Parallel Combination Circuits
Difficulty: Medium · Key topics: series-parallel reduction, equivalent resistance, re-drawing schematics, component failure analysis, terminal strips, battery load test
Most real circuits mix series and parallel parts, so this chapter gives a method for them. The core technique is stage-by-stage reduction: spot simple series or parallel groups, replace each with one equivalent resistor, repeat until one resistor is left, then find the total current and work backwards to every voltage drop and branch current. A section on re-drawing messy schematics shows how to trace loops from the battery and rebuild a clean vertical diagram. The chapter then returns to component failure analysis using what-if reasoning, and closes with building these circuits on breadboards and terminal strips, including why a battery must be checked under load.
Key Points:
- Apply the series rules to the series parts and the parallel rules to the parallel parts, selectively.
- The routine is: reduce to one equivalent resistor, find total resistance, find total current (I = E/R), then work backwards.
- Wires can be lengthened, shortened or moved without changing the circuit; only the order of connections matters.
- To re-draw a tangled schematic, trace each loop from one battery terminal to the other and mark the voltage polarities as you go.
- Before calculating a fault, predict whether each voltage and current will rise, fall or stay the same; this is how skilled troubleshooters think.
- Put no more than two wire ends or component leads under one terminal-strip screw.
- A battery that reads close to normal with no load can collapse when a load is connected, so test under load.
Practice Tip: After each reduction step, re-draw the circuit on paper with the new equivalent resistor in place, so you never reduce a part of the circuit you have already merged.
Common Mistake: Calling two resistors parallel just because they are drawn side by side. Check that both ends of each are connected to the same two points.
Important Questions:
- What is the method for solving a series-parallel circuit? Reduce it stage by stage to a single equivalent resistor, calculate total resistance and total current, then work back through each stage to find the voltage drop and current of every part.
- Why is a voltmeter reading with no load not enough to test a battery? A weak battery can still show nearly full voltage with no load, but when a load draws current its voltage falls sharply, so only a test under load shows its true condition.
Chapter 8: DC Metering Circuits
Difficulty: Medium · Key topics: meter movement, multiplier and shunt resistors, meter loading, ohmmeter, multimeter, Kelvin four-wire method, Wheatstone bridge, wattmeter
This is a design chapter about instruments, built mostly around analog meter movements. It starts with the movement types, electromagnetic (D’Arsonval, Weston, iron-vane) and electrostatic, then builds a voltmeter by adding a series multiplier resistor and an ammeter by adding a parallel shunt. Meter loading is treated for both: an ideal voltmeter has infinite resistance and an ideal ammeter zero, and null-balance voltmeters and clamp-on ammeters reduce the disturbance. The chapter then covers ohmmeters, hand-cranked high-voltage ohmmeters, multimeters, Kelvin four-wire measurement, Wheatstone and Kelvin bridges, wattmeters and ways to make precise custom resistances.
Key Points:
- A voltmeter gets its ranges from series multiplier resistors; an ammeter gets its ranges from parallel shunt resistors.
- An ideal voltmeter has infinite resistance and an ideal ammeter has zero resistance; anything else loads the circuit being measured.
- An analog ohmmeter reads zero ohms at full scale and infinity at rest, and its scale is nonlinear.
- Never connect an ohmmeter to a circuit that has its own source of voltage.
- A clamp-on ammeter senses the magnetic field around a wire, so it measures current without becoming part of the circuit.
- Kelvin (four-wire) measurement uses separate current and voltage leads so the lead resistance does not enter the reading.
- A Wheatstone bridge compares an unknown resistor with known ones until a null detector reads zero.
Memory Tip: Volts across, amps through: a voltmeter goes across two points and has high resistance, while an ammeter goes in line with the current and has almost none.
Common Mistake: Connecting an ammeter across a battery or other voltage source. Its tiny resistance makes a short circuit, which can blow a fuse or damage the meter.
Important Questions:
- A 1 mA, 100 Ω movement must read 10 mA full scale. What shunt is needed? The movement drops 0.1 V at full scale and the shunt must carry the other 9 mA, so Rshunt = 0.1/0.009 = about 11.1 Ω.
- Why does a voltmeter of low internal resistance give a wrong reading? It draws current from the circuit and changes the voltage it is meant to measure, so a good voltmeter must have very high resistance.
Chapter 9: Electrical Instrumentation Signals
Difficulty: Medium · Key topics: analog signals, live zero, voltage signals, 4 to 20 mA current loop, tachogenerator, thermocouple, pH electrode, strain gauge
This chapter shows how electricity carries measurement information in industrial systems. It separates analog signals, which vary continuously, from digital ones and mentions pneumatic signals as the older standard. Voltage signal systems are simple but lose accuracy to line resistance, so current loops, above all the 4 to 20 mA standard with its live zero, take over. The chapter then looks at sensors that turn physical quantities into electrical ones: tachogenerators for shaft speed, thermocouples (Seebeck effect, reference junctions, thermopiles and the Peltier effect), pH electrodes with the logarithmic pH scale, and strain gauges read through bridge circuits.
Key Points:
- An analog signal can vary continuously to represent any small change in the measured quantity.
- A live zero uses a non-zero value, such as 4 mA, for 0 percent so that a dead signal can be told apart from a true zero.
- A current loop is a series circuit, so the current is the same everywhere and wire resistance cannot distort the signal.
- The Seebeck effect gives a voltage between two joined dissimilar metals that is proportional to the junction temperature; a reference junction is always needed.
- pH is the negative base-ten logarithm of the hydrogen-ion concentration, and a glass electrode gives about 59.16 mV per pH unit.
- The glass membrane of a pH electrode has very high resistance, so a voltmeter of extremely high input resistance is required.
- A strain gauge changes resistance under load and is measured in a bridge, which also helps cancel temperature effects.
Memory Tip: On a 4 to 20 mA loop, 4 mA means 0 percent, 12 mA means 50 percent, 20 mA means 100 percent, and 0 mA means the loop is broken.
Common Mistake: Expecting a zero measurement to show as 0 mA on a live-zero loop. A reading of 0 mA is a fault, not a measurement.
Important Questions:
- Why do plants prefer a 4 to 20 mA current signal to a voltage signal? The loop is a series circuit, so the same current flows at both ends regardless of wire resistance, while a voltage signal loses accuracy to the drop along the line.
- Why does a thermocouple circuit need a reference junction? The voltage depends on the temperature difference between the measurement junction and the other junction in the circuit, so the temperature of that reference junction must be known or compensated.
Chapter 10: DC Network Analysis
Difficulty: Hard · Key topics: branch current, mesh current, node voltage, Millman, superposition, Thevenin, Norton, maximum power transfer, delta-Y conversion
When a circuit cannot be reduced with series-parallel rules, this chapter shows how to write enough equations to solve it. The branch current method combines KCL and KVL with assumed current directions, the mesh current method writes KVL around loops and has a shortcut “by inspection” pattern, and the node voltage method writes KCL at nodes using conductances. The second half covers network theorems: Millman’s, Superposition, Thevenin’s, Norton’s, the Thevenin-Norton conversion, Maximum Power Transfer (load equal to the source resistance) and delta-Y conversions, which turn a bridge into a series-parallel circuit.
Key Points:
- Branch current: assume directions, write KCL at a node and KVL on the loops, and solve; a negative answer means the assumed direction was wrong.
- Mesh current: assign one loop current per mesh; a part shared by two meshes carries their sum or difference.
- Node voltage: pick a reference node and write KCL equations in terms of conductances.
- Superposition: use one source at a time, replacing voltage sources with wires and current sources with opens, then add the results algebraically.
- Thevenin: find the open-circuit voltage at the load terminals and the resistance with sources removed; Norton uses the short-circuit current with the same resistance, and ETh = IN x RN.
- Maximum power reaches a load when its resistance equals the Thevenin (or Norton) resistance, which is not the same as maximum efficiency.
- Delta (pi) and Y (tee) networks can be converted with formulas so that the three terminals behave identically.
Practice Tip: Solve one two-loop circuit by the branch current method, then by the mesh method, and then check both answers in SPICE; all three must agree.
Common Mistake: Getting the source replacement backwards in Superposition and Thevenin. A removed voltage source becomes a wire (short), and a removed current source becomes a break (open).
Important Questions:
- What are the steps of Thevenin’s theorem? Remove the load and find the open-circuit voltage; remove the sources and find the resistance between the same terminals; draw the voltage source in series with that resistance; then reconnect the load and solve the simple series circuit.
- For what load does a source with a Thevenin resistance of 8 Ω deliver maximum power? A load of 8 Ω, because maximum power transfer occurs when the load equals the Thevenin resistance.
Chapter 11: Batteries and Power Systems
Difficulty: Easy · Key topics: electrochemical cell, primary and secondary cells, lead-acid cell, series and parallel banks, amp-hour rating, fuel and solar cells
The chapter explains where the voltage in a circuit comes from. It starts with electron activity in chemical reactions: molecules, ionic bonds and the electrochemical reactions that a cell harnesses. Primary cells cannot be practically recharged, while secondary cells such as the lead-acid cell can, and a hydrometer shows the state of charge of a lead-acid cell. Battery construction shows how series cells raise voltage and parallel cells lower resistance, with cell size setting internal resistance. Ratings, mainly amp-hours, follow, then special-purpose cells (mercury standard, fuel, solar and chemical detection cells) and practical advice on battery banks.
Key Points:
- A cell is one electrochemical unit; a battery is a group of cells connected for more voltage or more current.
- A primary cell cannot be practically recharged; a secondary cell is recharged by forcing current backwards through it.
- Series cells add voltage but not amp-hour capacity; parallel cells add current capacity and amp-hours at the same voltage.
- The larger the cell, the lower its internal resistance and the more current it can supply.
- An amp-hour rating is continuous current multiplied by discharge time, and it is only an approximation at the rated current.
- The best test for a dead battery is its voltage under load.
- Water-based batteries can give off explosive hydrogen gas, so charge them in ventilated places.
Memory Tip: Series adds volts; parallel adds amp-hours.
Common Mistake: Extending an amp-hour rating without limit. A 100 Ah battery does not necessarily give 100 A for one hour, because the rating holds only near the specified current or time.
Important Questions:
- How long can a 100 Ah battery supply a steady 5 A? About 100/5 = 20 hours, as an approximation at that discharge rate.
- What is the difference between a primary and a secondary cell? A primary cell cannot be practically recharged once its chemicals are used up; a secondary cell can be recharged by forcing current through it in the reverse direction.
Chapter 12: Physics of Conductors and Insulators
Difficulty: Medium · Key topics: wire size, circular mils, gauge, ampacity, fuses and breakers, specific resistance, temperature coefficient, superconductivity, dielectric strength
This chapter looks at the real wire behind the ideal zero-resistance wire of earlier chapters. It covers conductor size (diameter in mils, area in square and circular mils, the gauge system and busbars), ampacity, the allowable current set by heating, and fuses and circuit breakers, including fast and slow ratings and where a fuse belongs. It then treats specific resistance (R = ρl/A), the temperature coefficient of resistance, superconductivity with its transition temperature, and the breakdown voltage, or dielectric strength, of insulators. The chapter uses American units such as mils, circular mils and gauge, with metric conversions.
Key Points:
- Resistance rises with length and falls with cross-sectional area: R = ρl/A, where ρ is the specific resistance of the material.
- A circular mil is the diameter in mils squared, so the area in circular mils is d2 and no π is needed.
- In the gauge system a larger number means thinner wire, and sizes thicker than 1 are written 0, 00, 000 and 0000.
- Ampacity is the safe current limit set by heat; thin wire has lower ampacity than thick wire.
- R = Rref [1 + α(T – Tref)]; pure metals have a positive coefficient and carbon, silicon and germanium a negative one.
- A fuse belongs in the ungrounded conductor, so that a blown fuse leaves only the safe grounded conductor attached to the load.
- Superconductors have exactly zero resistance below their transition temperature, and an insulator breaks down at its dielectric strength, quoted in volts per mil.
Memory Tip: Think of a hose: long and thin means high resistance, short and fat means low resistance.
Common Mistake: Using a table value of specific resistance at the wrong temperature. Such figures are given at a standard temperature (usually 20 or 25 °C) and must be corrected with the temperature coefficient.
Important Questions:
- What is the area in circular mils of a wire 10 mils in diameter? A = d2 = 10 x 10 = 100 circular mils.
- What does ampacity mean, and why is thin wire limited? It is the largest current a wire can carry safely; thin wire has more resistance per unit length, so it makes more heat per amp and can become a fire hazard.
Chapter 13: Capacitors
Difficulty: Medium · Key topics: electric field, capacitance, farad, i = C dv/dt, plate area and spacing, dielectric, series and parallel capacitors, working voltage, polarity
Capacitors are introduced through the electric field that exists whenever voltage separates two conductors. A capacitor opposes changes in voltage: it acts as a load when the voltage rises and as a source when the voltage falls, and capacitance is measured in farads. The calculus section gives i = C dv/dt and explains instantaneous current and rate of change. The chapter then lists the factors that set capacitance (plate area, plate spacing and the dielectric material), shows that capacitances add in parallel and diminish in series, and ends with practical limits such as working voltage and the polarity of some capacitors.
Key Points:
- Capacitance is the ability to store energy in an electric field and to oppose changes in voltage; the unit is the farad.
- The relation is i = C dv/dt: current depends on how fast the voltage changes, so a steady DC voltage means zero current.
- Larger plate area raises capacitance, wider plate spacing lowers it, and the dielectric material also matters.
- Parallel capacitances add, Ctotal = C1 + C2; in series they diminish, 1/Ctotal = 1/C1 + 1/C2.
- Every capacitor has a working voltage, and exceeding it can break down the dielectric and short the capacitor.
- Some capacitors are polarized and tolerate voltage in one direction only.
Memory Tip: A capacitor resists a change in voltage the way a flywheel resists a change in speed.
Common Mistake: Treating a capacitor like a resistor with a fixed number of ohms. Its current follows the rate of change of voltage, not the voltage itself.
Important Questions:
- How does a capacitor behave when the voltage across it is rising? It acts as a load: it draws current and absorbs energy into its electric field, and when the voltage falls it acts as a source and releases that energy.
- What is the total capacitance of two 10 μF capacitors in series? 1/C = 1/10 + 1/10 = 1/5, so C = 5 μF; in parallel they would give 20 μF.
Chapter 14: Magnetism and Electromagnetism
Difficulty: Medium · Key topics: permanent magnets, retentivity, left-hand rule, mmf, magnetic units, permeability, saturation, hysteresis, Faraday’s law, mutual inductance
This chapter prepares the ground for inductors. It begins with permanent magnets (lodestone, retentivity, and ferromagnetic, paramagnetic and diamagnetic materials), then Oersted’s discovery that current produces a magnetic field, the left-hand rule for electron flow and the way a coil multiplies the field. Magnetic units are covered, with field force (mmf), flux, field intensity H and flux density B, and the several unit systems in use. Permeability and saturation introduce the magnetization curve and hysteresis. The chapter ends with Faraday’s electromagnetic induction, e = N dΦ/dt, and mutual inductance, which is how a transformer works.
Key Points:
- Retentivity is the ability of a material to keep its magnetism; ferromagnetic materials magnetize easily and diamagnetic ones repel a field.
- Current in a wire makes a circular magnetic field; the left-hand rule uses the thumb along the electron flow.
- The mmf of an electromagnet is proportional to current times the number of turns (ampere-turns).
- Field intensity H is mmf per unit length and flux density B is flux per unit area; the B-H curve shows permeability changing with field.
- Saturation is the point where no more flux can be forced into a material, and hysteresis is caused by retentivity.
- Faraday’s law: induced voltage e = N dΦ/dt, which needs a changing flux.
- A transformer works through mutual inductance and needs changing voltage, so it is an AC device and not a DC device.
Memory Tip: No change, no voltage: a steady magnetic flux induces nothing, and only a changing flux does.
Common Mistake: Expecting a transformer to work on steady DC. With a constant current the flux is constant, so no voltage is induced in the second coil.
Important Questions:
- What does Faraday’s law of electromagnetic induction state? The voltage induced in a coil is equal to the number of turns times the rate of change of magnetic flux, e = N dΦ/dt.
- A coil of 200 turns carries 0.5 A. What is its magnetomotive force? mmf = turns x current = 200 x 0.5 = 100 ampere-turns.
Chapter 15: Inductors
Difficulty: Medium · Key topics: inductance, henry, v = L di/dt, turns, core material, series and parallel inductors, rated current, equivalent circuit
Inductors are the magnetic counterpart of capacitors. An inductor opposes changes in current: it drops a voltage that opposes a rising current, acting as a load, and creates a voltage that supports a falling current, acting as a source, with inductance measured in henrys. The calculus section gives v = L di/dt, matching the capacitor form of the previous chapter. The chapter then lists the factors that decide inductance, including the number of turns and the core material, shows that inductances add in series and diminish in parallel, and ends with practical limits such as rated current and the wire resistance of a real coil.
Key Points:
- An inductor stores energy in a magnetic field and opposes changes in current; the unit is the henry, and older names are choke and reactor.
- The relation is v = L di/dt, so a steady DC current gives zero voltage and the inductor acts like a plain wire.
- Inductance rises with more turns of wire and with a core of higher permeability.
- Series inductances add; parallel inductances diminish, which is the reverse of capacitors.
- A real inductor has some wire resistance, so there is no such thing as a perfect inductor.
- The rated current of an inductor is limited by the heat its wire can dissipate.
Memory Tip: Capacitors fight changes in voltage; inductors fight changes in current.
Common Mistake: Mixing up the combining rules. Capacitors add in parallel, but inductors add in series.
Important Questions:
- How do inductors combine in series and in parallel? In series the inductances add, Ltotal = L1 + L2; in parallel they diminish, like parallel resistors.
- What is the voltage across an ideal inductor carrying a steady DC current? Zero, because v = L di/dt and the current is not changing, so di/dt is zero.
Chapter 16: RC and L/R Time Constants
Difficulty: Hard · Key topics: transients, time constant, capacitor and inductor charging, universal time constant formula, non-zero start, Thevenin equivalent, solving for time
The final chapter puts capacitors and inductors to work in time. After a sudden DC change, a capacitor in series with a resistor charges with its current falling from maximum to zero while its voltage rises; an inductor does the opposite, starting as an open circuit and ending as a short. The universal time constant formula, Change = (Final – Start)(1 – e-t/τ), with τ = RC or L/R, solves both. The chapter explains why the inductive constant is L/R and not LR, extends the method to circuits that start from non-zero values, reduces complex circuits to Thevenin equivalents, and rearranges the formula with natural logarithms to find the time needed to reach a value.
Key Points:
- The time constant is τ = RC (seconds) for a capacitor circuit and τ = L/R (seconds) for an inductor circuit.
- A discharged capacitor acts as a short at first and as an open circuit at the end; an inductor with no current acts as an open circuit at first and a short at the end.
- The quantity to calculate is the one the part opposes changing: voltage for a capacitor and current for an inductor.
- The method: find τ, pick the quantity, note its start and final values, apply the universal formula, and add the change to the start value if it is not zero.
- RC circuits are faster with low resistance, but L/R circuits are faster with high resistance.
- For complex circuits, treat the reactive part as the load and reduce the rest to a Thevenin equivalent.
- To find the time to reach a given value, use t = -τ ln(1 – Change/(Final – Start)).
Practice Tip: Simulate an RC charging circuit with a SPICE transient analysis and read the capacitor voltage at t = RC; it should be about 63 percent of the final value.
Common Mistake: Using LR instead of L/R for the inductive time constant. Because of the division, a bigger resistance makes an inductive circuit respond faster, not slower.
Important Questions:
- What is the time constant of a 10 kΩ resistor in series with a 100 μF capacitor? τ = RC = 10,000 x 0.0001 = 1 second.
- How much of the change has happened after one time constant? About 63 percent, because 1 – e-1 is about 0.632; after five time constants the circuit is about 99 percent of the way to its final value.
Appendices A-1 to A-3: About This Book, Contributor List and License
Appendix · Difficulty: Easy · Key topics: open textbook, copyleft, SPICE, contributors, Creative Commons licence
Appendix A-1 explains why the book exists. Kuphaldt, an industrial electronics instructor, found his first-year textbook full of errors and expensive, so he compiled his own notes and made the book free and open for anyone to copy or improve. He explains the licences he tried (first the GPL, then the Design Science License, and later Creative Commons) and why SPICE listings appear throughout: readers can watch circuits behave rather than take statements on faith. He also warns that electricity can kill, so experiments should use only small batteries. Appendix A-2 explains how to contribute and credits the volunteers, and Appendix A-3 holds the licence.
Key Points:
- The book is an open text: anyone may copy and share it, and modified versions must credit the original author and contributors.
- The author’s current edition uses Creative Commons Attribution 4.0 (CC BY 4.0); older copies, including many PDFs still in circulation, carry the Design Science License.
- SPICE is used inside the text so that readers learn by observing simulated circuits as well as by reading explanations.
- Appendix A-2 credits major contributors with their contribution and minor ones by name only.
- Experiment only with small battery circuits; high-power circuits are for trained professionals.
Important Questions:
- Why does the book include SPICE listings? They let the reader observe circuit behavior inductively by reading the simulation output, add empirical proof to the text, and teach a free tool that can be used for safe experiments.
- What must you do if you share or adapt the book? Give credit to the author (and the other contributors), and say what you changed; under CC BY you may otherwise copy, share and adapt it freely.
How to Study This Book
The book declares no parts, so your course outline decides the chapters. A first Basic Electrical Circuits or Circuit Analysis (DC) course in BSEE or BSET usually draws on Chapters 1 and 2 (the basics and Ohm’s law), 5 to 7 (series, parallel and combination circuits) and 10 (network analysis). Chapter 8 serves the lab and instrumentation side, Chapters 11 and 12 are background on sources and wires, and Chapters 13 to 16 are the first look at capacitors, inductors and transients. A BSCS student who only needs electronics basics can stop after Chapters 1, 2, 4, 5 and 6, with Chapter 7 as a bonus.
Read Chapters 1 and 2 even if the ideas are familiar. Voltage, current, resistance, power and the three forms of Ohm’s law are used on every later page, and the water-pipe and marble analogies are worth keeping. Read Chapter 3 before your first lab session. It is a good introduction to lock-out and tag-out, grounding and meter safety, but it does not replace the safety training your lab gives you. Chapter 4 is a quick toolkit; do its prefix conversions until they are automatic.
Chapters 5 to 7 are the heart of the book for exams. Fill in the voltage-current-resistance table for every circuit you meet and apply the series and parallel rules across the rows. Do the failure-analysis sections as predictions first (does this voltage go up, down or stay the same?) and then check by calculation. Chapter 6 gives two tools, the dividers and Kirchhoff’s laws, that you will use for the rest of your degree.
Chapter 10 is the hardest chapter of the first half. Learn the three equation methods in order (branch current, mesh current, node voltage), then do each theorem example by a second method so that you can check yourself. Superposition, Thevenin and Norton come up again and again in later circuits courses, so treat their step lists as things to memorize. The delta-Y section is short but is a favorite exam question for bridge circuits.
Chapter 8 spends most of its pages on analog meter movements and pre-transistor multimeters. Learn the multiplier and shunt ideas, meter loading, the four-wire method and the Wheatstone bridge, and skim the vintage hardware. Chapter 9 is for instrumentation and control readers; the 4 to 20 mA loop and the thermocouple section are the parts most worth keeping. Chapter 11 has no lithium-ion material, so take battery chemistry for modern cells from your course notes. Chapter 12 works in American units (mils, circular mils, gauge and the National Electrical Code), although it gives metric conversions, so be ready to convert if your course uses square millimetres.
Chapters 13 to 16 use a little calculus: the i = C dv/dt and v = L di/dt sections assume you know what a derivative means, and Chapter 16 uses ex and natural logarithms. If you have not met derivatives yet, learn the formulas and the shapes of the charging curves first and come back to the calculus later. Chapter 14 is background for Chapter 15, so read it first. This volume is DC only: AC circuits, reactance, phasors and resonance are in Volume II of the same series, so a full circuits course will need that or your class notes.
Know what the book does not offer. It has worked examples and short review lists inside the chapters but no end-of-chapter problem sets and no answer keys, so make your own problems and check them in SPICE or against your textbook. Its figures carry much of the explanation, so read it with the diagrams in front of you, not just the text of this page.
Used In These Programs
This book is part of the Circuit Analysis (DC) course in: BS Electrical Engineering · BS Computer Science · BS Engineering Technology. Browse all Circuit Analysis books or all Engineering books.
Who Should Read This
This book is written for first-year students of BSEE and BSET who are taking Basic Electrical Circuits or DC Circuit Analysis, for BSCS students who need electronics basics before digital logic or computer organization, and for technicians and self-learners who are completely new to electronics. It assumes arithmetic and basic algebra; calculus helps only in the capacitor and inductor sections. The explanations are plain and the analogies are friendly; the author wanted a text that was neither too heavy on mathematics nor too thin on information, which makes it a good entry text for students who have never touched a circuit. It is not the right choice if you need problem sets with answers, AC analysis, or semiconductor devices, which belong to other volumes of the series. For the field theory behind Chapters 13 to 15, pair it with University Physics Volume 2, and brush up your derivatives with Calculus Volume 1 before the calculus sections. The chapters on Ohm’s law, series and parallel circuits and Kirchhoff’s laws are also useful revision of current electricity before engineering entry tests.
Applicable Universities
This book is useful for students at Pakistani universities offering BS Electrical Engineering, BS Engineering Technology and BSCS including UET, NUST, COMSATS, FAST, Punjab University, Virtual University, and other HEC-recognized institutions.
Official Copy of Lessons in Electric Circuits Volume I DC
The author gives the whole book away free on his own site, as a PDF and as chapter-by-chapter web pages. Click below to open the official page and download the PDF.
→ Visit Official PageFAQs
Is Lessons in Electric Circuits Volume I DC free?
Yes. The author’s site gives the book as a free download, with a copyright line of 2000 to 2023, and points to the Creative Commons Attribution 4.0 International licence (CC BY 4.0) in Appendix 3, so you may copy, share and adapt it as long as you credit Tony R. Kuphaldt. Older copies of the PDF that are still in circulation carry the earlier Design Science License, which also allows free copying with credit.
Which edition is this?
It is the Fifth Edition. The PDF title page says last update October 18, 2006, and the author’s index page shows a minor revision on February 3, 2023. The book has been maintained as an open text for more than twenty years, and its core DC theory has not changed.
How many chapters and exercises does it have?
There are 16 chapters and three appendices (About This Book, Contributor List and the licence). The chapters have worked examples and short review lists, but no end-of-chapter problem sets and no answer keys, so you need your class problems or your own for practice.
Is it good for complete beginners?
Yes. It assumes only arithmetic and basic algebra and starts from static electricity and the atom. Chapters 13, 15 and 16 include sections on calculus, so learn what a derivative means before you reach them. Complete beginners should read the chapters in order.
Does it cover Kirchhoff’s laws, Thevenin, Norton and superposition?
Yes. Kirchhoff’s Voltage and Current Laws and the voltage and current dividers are in Chapter 6. Chapter 10 covers the branch current, mesh current and node voltage methods, Millman’s, Superposition, Thevenin’s and Norton’s theorems, maximum power transfer and delta-Y conversions.
Does it cover AC circuits, and is it still current in 2026?
This volume is DC only. AC circuits, phasors and resonance are in Volume II of the same series. The DC theory is timeless, but Chapter 8 is built around analog meters, Chapter 11 has no lithium-ion material and Chapter 12 uses American wire units, so take modern details from your lecture notes.
Related Books
- University Physics Volume 2 – OpenStax (the electric and magnetic fields behind Chapters 13 to 15)
- College Physics 2e – OpenStax (a gentler algebra-based route to current and circuits)
- Calculus Volume 1 – OpenStax (the derivatives in i = C dv/dt and v = L di/dt)
- Elementary Differential Equations – Trench (the mathematics behind RC and L/R transients)
Lessons in Electric Circuits, Volume I: DC gives you a free, patient route from the first idea of voltage to network theorems, capacitors, inductors and time constants, with worked examples and SPICE in every chapter. Browse more Engineering books for the rest of your semester.
Lessons in Electric Circuits, Volume I: DC by Tony R. Kuphaldt, copyright 2000-2023, Fifth Edition, last update October 18, 2006 (minor revision February 3, 2023). Licensed under the Creative Commons Attribution 4.0 International licence (CC BY 4.0) in the author’s current edition; earlier copies of the book carry the Design Science License. Major contributors are credited in Appendix 2 of the book. Official source: https://www.ibiblio.org/kuphaldt/electricCircuits/DC/index.html
© Copyright Policy
Freebooks.pk is an educational resource for students in Pakistan. Textbooks and other books belong to their respective boards, authors and publishers, and all rights remain with them. If you are the copyright holder of any material on this page and want it changed or removed, please contact us or file a request under our DMCA policy. We review every request and remove reported content promptly.
