BS Mechanical Engineering and BS Chemical Engineering students who need a free thermodynamics text can use this guide to study Engineering Thermodynamics: A Graphical Approach by Israel Urieli of Ohio University. It runs to 509 pages in 11 chapters across two parts and was written as a self-contained two-course sequence. Rather than teaching one component at a time, it applies the First and Second Laws to whole systems: the Stirling engine, Diesel and Otto engines, steam power plants and refrigerators. Its signature tool is the picture. You sketch the states on a T-v, P-h or h-s diagram first, and the numbers follow.
Part 1 covers units, properties of pure substances, the First Law for closed systems and control volumes, the Second Law, and entropy. Part 2 adds exergy, regenerative steam cycles, CO2 refrigeration, air-water mixtures with cooling towers, and combustion. Fifteen appendices carry steam, R134a and CO2 tables, so the PDF works on its own. Two honest notes: this is the 2021 text version of the author’s web resource, so the animations and videos it links to are not inside the file, and its forecast for CO2 in car air conditioning has not played out.
Book Overview
| Course | Engineering Thermodynamics (two-course sequence) |
| Degree Programs | BS Mechanical Engineering (BSME), BS Chemical Engineering (BSChE) |
| Level | University / Undergraduate — Thermodynamics I and II |
| Edition | OHIO Open Faculty Textbooks, 2021 — the text version of the author’s web resource |
| Author | Israel Urieli, Associate Professor Emeritus of Mechanical Engineering, Ohio University |
| Publisher | OHIO Open Library, Ohio University |
| Structure | 11 chapters in two parts (Part 1: Chapters 1–6; Part 2: Chapters 7–11), most split into lettered sections, plus 15 appendices (A–O) |
| Pages | 509 pages |
| Exercises | Solved problems and numbered problems with final answers printed in brackets, plus short quick quizzes; no separate answer key |
| Language | English |
| License | Creative Commons Attribution-NonCommercial-ShareAlike 3.0 United States (CC BY-NC-SA 3.0 US), as printed in the book; the repository record lists the same work under CC BY-NC-SA 4.0 |
| Format | Free PDF (about 11.7 MB) from the OHIO Open Library, with a separate properties tables booklet on the same page |
Chapter List
Chapter 1: Introductory Concepts, Units, and Definitions
Part 1: First and Second Laws · Difficulty: Easy · Key topics: SI units, force and work, forms of energy, closed system, control volume, intensive and extensive properties, state postulate, process and cycle, gage and absolute pressure, manometer, barometer, temperature scales
The book opens by calling thermodynamics the science of energy and stating the conservation of energy. It insists on SI units, recalls the Mars Climate Orbiter lost to a unit-conversion error, explains the lbm/lbf confusion, and gives US students a short units survival kit. Potential, kinetic and internal energy are compared with a joke about cooking a turkey by dropping it from a 100 m building (about 0.33°C per fall). Then come closed systems and steady-flow control volumes, extensive, intensive and specific properties, the state postulate, quasi-static processes and cycles, pressure measurement with manometers and a barometer, and temperature scales. A building-height example ends in an uncertainty analysis that shows a barometer gives only about 100 ± 42 m.
Key Points:
- Energy cannot be created or destroyed; the book tracks stored energy (PE, KE, internal energy U) and energy in transit (work W and heat Q)
- A closed system (control mass) has no mass crossing its boundary; a control volume does, and the book treats only steady-flow control volumes
- An extensive property depends on mass; an intensive property does not; a specific property is an extensive one divided by mass
- State postulate: two independent intensive properties fix the state, so two-dimensional plots are enough
- Absolute pressure = gage pressure + atmospheric pressure; 1 bar = 100 kPa and 1 atm = 101.32 kPa
- Absolute temperature scales (K and R) are needed for gas equations; −40°C equals −40°F
- When a result depends on the difference of two large numbers, small measurement errors are magnified
Memory Tip: A specific property always has kilograms in the denominator of its unit (kJ/kg, m3/kg). If the unit has no kg underneath, it is extensive.
Common Mistake: Putting gage pressure or Celsius temperature into a gas equation. Pressure and temperature must be absolute there.
Important Questions:
- What is the difference between a closed system and a control volume? A closed system holds a fixed mass and exchanges only heat and work across its boundary. A control volume also has mass flowing in and out through inlet and outlet ports.
- A gage reads 200 kPa where the atmosphere is 100 kPa. What is the absolute pressure? P(abs) = P(gage) + P(atm) = 300 kPa.
Chapter 2: Properties of Pure Substances (Parts A and B)
Part 1: First and Second Laws · Difficulty: Medium · Key topics: phase change, saturation, quality, T-v and P-v diagrams, property tables, interpolation, ideal gas equation, gas constant, compressibility factor, Lee-Kesler chart
Part A follows liquid water heated at constant pressure in a piston-cylinder device from 20°C: compressed liquid, saturated liquid, a mixture, saturated vapor, then superheated steam. Repeating this at higher pressures shrinks the mixture region until the critical point. The author prefers the name quality region and defines quality as vapor mass over total mass, linking it to turbine blade erosion. Tables are used with hand-sketched T-v and P-v diagrams and linear interpolation. Part B introduces the ideal gas equation (under 1% error in a marked zone), applies it to a car tire, atmospheric pressure with altitude and a hot-air balloon, and uses the compressibility factor Z with the Lee-Kesler chart near the critical point.
Key Points:
- Subscript f marks saturated liquid and g marks saturated vapor; superheated steam has T above Tsat at that pressure
- Quality x = mass of vapor / total mass, so the mixture volume obeys v = vf + x(vg − vf); u, h and s follow the same pattern
- Above the critical point there is no clear line between liquid and vapor
- Always begin with a labelled sketch of the states on a T-v or P-v diagram, even though it is not drawn to scale
- Ideal gas equation: Pv = RT, or PV = mRT, with absolute P and T; it works well when volume is far above the critical volume
- Compressibility factor Z = Pv/RT; Z close to 1 means ideal gas behaviour, and reduced pressure and temperature (P/Pcr, T/Tcr) let one chart serve many fluids
- Rule of thumb: P well below Pcr, or T well above Tcr, is probably an ideal gas; if in doubt, check Z
Memory Tip: Read x as a dial: x = 0 is saturated liquid (all f) and x = 1 is saturated vapor (all g). The quality only exists between the two saturation lines.
Common Mistake: Using quality for a state that is not inside the dome. Always compare the given specific volume with vf and vg first; the book does this in its two-step heating example, where the final state turns out to be superheated.
Important Questions:
- How is the quality of a liquid-vapor mixture found? Compute the specific volume v = V/m and place it between the saturated values at that pressure: x = (v − vf)/(vg − vf).
- When can steam be treated as an ideal gas? At low pressure or high temperature, far from the saturation lines and the critical point; the book marks a zone on the T-v diagram where the error is under 1%.
Chapter 3: The First Law of Thermodynamics for Closed Systems (Parts A to D)
Part 1: First and Second Laws · Difficulty: Medium · Key topics: heat and work sign convention, boundary work, internal energy, enthalpy, specific heats of ideal gas, Stirling engine and cooler, regenerator, Diesel cycle, Otto cycle, air-standard analysis
Part A states the closed-system energy equation, takes boundary work as the area under the P-v curve, and defines enthalpy h = u + Pv. From Joule’s 1843 experiment, internal energy and enthalpy of an ideal gas depend on temperature only, which leads to Cv, Cp, R and k. Part B analyses the ideal Stirling engine as four processes with a regenerator, then the reversed cooler. Parts C and D apply the same method to the air-standard Diesel and Otto cycles, with adiabatic relations built from the energy equation and with specific heats taken at a typical average cycle temperature instead of 300 K.
Key Points:
- Sign convention: heat into the system and work done by the system are positive; boundary work is W = ∫ P dV
- Work and heat are path functions; internal energy and enthalpy are properties
- For an ideal gas, du = Cv dT and dh = Cp dT, with R = Cp − Cv and k = Cp/Cv; Cp and Cv are constant only for monatomic gases such as helium and argon
- Ideal Stirling cycle: isothermal compression, constant-volume displacement through the regenerator, isothermal expansion, constant-volume displacement back; with perfect regeneration its efficiency equals the Carnot efficiency
- Without a regenerator the efficiency falls to Wnet/(Qin + QR), and the author says real machines reach only about 40 to 50% of the ideal
- Diesel: air alone is compressed (ratio usually above 16:1) until the fuel ignites; heat is added at constant pressure, described by a cutoff ratio
- Otto: fuel and air are compressed at around 8:1 and ignited by a spark, which adds heat at constant volume; efficiency can be written from k and the compression ratio r
Memory Tip: Think of the regenerator as a heat bank. The hot gas deposits heat in it while moving to the cold side, and the cold gas withdraws the same heat on the way back, so the heater never has to pay for it.
Common Mistake: Using the 300 K specific-heat values for a whole Diesel or Otto cycle although the gas reaches well over 1000 K. The book picks values at a typical average temperature (900 K in its examples) and notes that the efficiencies are still unrealistically high because losses are ignored.
Important Questions:
- How do the Diesel and Otto ignition processes differ? In the Diesel cycle a high compression ratio heats the air enough to ignite injected fuel, which burns at constant pressure. In the Otto cycle a lower ratio is used and a spark ignites the premixed charge, so heat is added at constant volume.
- Why can an ideal Stirling engine match the Carnot efficiency? Heat is added and rejected isothermally, and the regenerator recovers the heat of the two constant-volume processes internally, so the only external heat flows are at the extreme temperatures.
Chapter 4: The First Law of Thermodynamics for Control Volumes (Parts A to D)
Part 1: First and Second Laws · Difficulty: Medium · one prediction in Part D has dated · Key topics: mass flow rate, flow work, steady-flow energy equation, P-h diagram, steam power plant, supercritical reheat plant, cogeneration, vapor-compression refrigeration, heat pump, COP, R134a, CO2 refrigerant
Part A derives the steady-flow energy equation in power form: mass flow is density times area times velocity, flow work is Pv, and u + Pv combine into enthalpy h. The pressure-enthalpy diagram becomes the main sketching tool. Part B takes a four-component steam plant (turbine, condenser, feedwater pump, boiler) and solves each part on its own, then scales up to a 25 MPa supercritical reheat plant modelled on the Gavin plant in Ohio, with cogeneration and hybrid variants. Part C does the same for R134a refrigerators, air conditioners and geothermal heat pumps. Part D introduces CO2 (R744) as a refrigerant and a transcritical heat-pump cycle.
Key Points:
- Steady flow means no accumulation, so the balance is written in kW: heat in minus shaft work out equals mass flow times the change in enthalpy h = u + Pv, where Pv is the flow work (kinetic and potential terms are added only when they matter)
- In the P-h diagram the boiler, condenser and evaporator are horizontal lines, so enthalpy differences show turbine work and heat transfer at a glance
- Compressed liquid enthalpy is taken as hf at the same temperature; the feedwater pump needs only about 1% of the turbine power in the book’s first plant
- Cooling the condenser needs a large water flow (421 kg/s for a 10°C rise in the simple example), which is why cooling towers appear later
- COP of a refrigerator = heat absorbed in the evaporator / compressor work; for a heat pump it is the heat rejected in the condenser / compressor work
- CO2 refrigeration runs at very high pressure with a very hot compressor outlet, and the book argues these traits allow compact units and combined space and water heating
- Dated prediction: the book expects CO2 to replace R134a in car air conditioning once Europe bans R134a; most new cars have since moved to another low-GWP refrigerant (R1234yf), while R744 is used mainly in commercial refrigeration and some heat pumps. The thermodynamics itself is unchanged
Memory Tip: On a P-h diagram, heat exchangers are horizontal lines because their pressure is constant, and the length of the line is the heat. Read the diagram like a bar chart before touching any numbers.
Common Mistake: Dropping the sign rule for COP. Compressor work is negative in the sign convention, yet COP is always quoted as a positive number, and a refrigerator and a heat pump use different heat terms for the same hardware.
Important Questions:
- Why is the feedwater pump power so small compared with the turbine? The pump handles liquid, which has a very small specific volume, so raising its pressure needs little work, while the turbine expands low-density steam.
- How do the COP of a refrigerator and of a heat pump differ? Both divide by compressor work; the refrigerator counts the heat absorbed at the evaporator, and the heat pump counts the heat delivered at the condenser.
Chapter 5: The Second Law of Thermodynamics
Part 1: First and Second Laws · Difficulty: Medium · Key topics: heat engine, heat pump, Kelvin-Planck and Clausius statements, reversibility, Carnot’s theorem and corollaries, Carnot efficiency, Carnot cycle, Stirling cycle
This short chapter steps back from specific machines. A heat engine and a heat pump are drawn as boxes between a hot and a cold reservoir, and the Second Law is given as two unprovable but never-violated statements, Kelvin-Planck and Clausius. The author shows they are equivalent by wiring a Clausius violator to an engine to build a Kelvin-Planck violator. Reversibility is set out as frictionless, quasi-equilibrium and isothermal heat transfer. Carnot’s theorem and two corollaries are proved by coupling an irreversible engine to a reversible one, giving the efficiency 1 − TL/TH. The Carnot cycle is called impractical, and the ideal Stirling engine is the practical comparison.
Key Points:
- Kelvin-Planck: no cyclic device can turn heat from one reservoir entirely into work
- Clausius: no cyclic device can move heat from a cold body to a hotter one with no other effect
- Three conditions for reversible operation: no friction, quasi-equilibrium at each step, and heat transfer only at equal temperatures
- Carnot’s theorem: no engine between two reservoirs beats a reversible one
- Corollary 1: all reversible engines between the same two reservoirs have the same efficiency; corollary 2: that efficiency depends only on the reservoir temperatures
- Replacing the heat ratio with a temperature ratio is valid only for reversible machines, with absolute temperatures
- At the same temperatures and compression ratio, the Stirling cycle gives much more net work per cycle than the Carnot cycle, with the same efficiency
Memory Tip: Kelvin-Planck forbids the perfect engine and Clausius forbids the perfect refrigerator. Both are statements about what is impossible.
Common Mistake: Using Celsius temperatures in 1 − TL/TH. Convert to kelvin first, or the efficiency comes out badly wrong.
Important Questions:
- What is the maximum efficiency of an engine between 800 K and 300 K? The Carnot value, 1 − 300/800 = 62.5%; any real engine does worse.
- Why are the Kelvin-Planck and Clausius statements equivalent? A device that breaks Clausius can be linked to an ordinary engine so that the cold reservoir drops out, leaving an engine that takes heat from one reservoir and produces work, which breaks Kelvin-Planck.
Chapter 6: Entropy – a New Property (Parts A and B)
Part 1: First and Second Laws · Difficulty: Hard · Key topics: Clausius inequality, entropy, increase in entropy principle, entropy generation, T ds relations, isentropic process, h-s Mollier diagram, turbine, pump and compressor efficiency, turbojet, gas turbine
Part A introduces entropy through the Clausius inequality as the reversible heat divided by temperature. The author explains it by analogy with work: work needs a pressure and a volume change, and heat needs a temperature and an entropy change. The increase in entropy principle gives Sgen ≥ 0 (zero for reversible processes), and the T ds relations are summarised in sheets in Appendix L. The ideal turbine becomes a vertical line on the h-s diagram, which defines adiabatic efficiency, applied to turbines, pumps and R134a and CO2 compressors. Part B analyses aircraft engines: an ideal turbojet and the T700 helicopter gas turbine with its gas-generator and power turbines.
Key Points:
- Entropy is defined by ds = δqrev/T, and total entropy change of system plus adiabatic surroundings is always zero or positive
- Entropy generated is zero only for reversible processes
- The ideal adiabatic turbine, compressor or nozzle is isentropic, which gives a benchmark for real equipment
- Turbine adiabatic efficiency = actual work / isentropic work; pump and compressor efficiency is isentropic work / actual work
- On the h-s (Mollier) diagram the actual expansion leans away from the vertical because entropy rises
- Liquid water is usually taken as incompressible in pumps, but at 25 MPa and above 100°C the book shows it is not, and compressed-liquid tables are needed
- The ideal T700 analysis gives more power than the real engine (around 1800 hp), because every component was taken as isentropic
Memory Tip: On an h-s chart the ideal turbine is a straight vertical drop and the real turbine leans to the right. The lean is the entropy generated, and the shorter drop is the lost work.
Common Mistake: Turning the efficiency formula upside down. A turbine delivers less than the isentropic work, so its ratio is actual over isentropic; a pump or compressor needs more than the isentropic work, so its ratio is isentropic over actual.
Important Questions:
- How is the adiabatic efficiency of a steam turbine defined? ηT = (h1 − h2a)/(h1 − h2s), the actual enthalpy drop divided by the drop for an isentropic expansion to the same exit pressure.
- What does the increase in entropy principle say? For any process, the entropy change of the system plus its adiabatic surroundings is greater than or equal to zero, with equality only for reversible processes.
Chapter 7: Exergy – Maximum Available Work Potential (Parts A to C)
Part 2: Applied Engineering Thermodynamics · Difficulty: Hard · Key topics: exergy, dead state, reversible work, irreversibility, second law efficiency, wind and hydro power, adiabatic compressor and turbine, heat transfer to a control volume
Part 2 begins by combining the First and Second Laws to find theoretical limits. Exergy is the maximum work a system can deliver relative to an environment, usually 1 atm and 25°C, and the dead state is reached when nothing more can be extracted. Two simple cases come first: wind power, where the kinetic energy of the air is the limit and the Betz limit of 59.3% applies in practice, and hydroelectric power, where all potential energy can become work. A steady-flow control volume then yields reversible work, irreversibility and second law efficiency. Part B builds reversible equivalent circuits for an adiabatic compressor and turbine, and Part C adds heat from a hot source.
Key Points:
- Exergy (availability) is the maximum work potential at a given state in a stated environment; the dead state has no work potential left
- Available wind power is proportional to the cube of the wind speed, so doubling the speed gives eight times the power
- Reversible work is the work with zero entropy generation; irreversibility is the gap between reversible and actual work
- Second law efficiency compares actual work with reversible work, for work-producing and work-consuming devices alike
- The reversible equivalent of an adiabatic compressor includes an inlet heat exchanger and a heat engine running off the environment at T0
- Exergy at a port equals the reversible work obtained when its fluid is brought down to the dead state
Memory Tip: Energy tells you how much you have; exergy tells you how much of it you can actually use. The environment you choose sets the baseline.
Common Mistake: Treating the isentropic work of Chapter 6 as the minimum compressor work. The book shows that the true reversible work also accounts for heat exchange with the environment at T0, so it is a different number.
Important Questions:
- What is the dead state? The condition in which the system is in complete equilibrium with its environment and has no kinetic or potential energy relative to it, so no more work can be extracted.
- How does available wind power depend on wind speed? It grows with the cube of the speed; the book’s example goes from a few hundred watts at an average breeze to several kilowatts in a strong winter wind.
Chapter 8: Steam Power Cycles (Parts A and B)
Part 2: Applied Engineering Thermodynamics · Difficulty: Hard · Key topics: ideal Rankine cycle, reheat, P-h diagram, steam quality, open feedwater heater, closed feedwater heater, bleed fraction, cogeneration, Gavin power plant
Chapter 8 returns to the steam plant now that entropy is known, using ideal isentropic turbines and pumps to find maximum performance. The author prefers P-h diagrams to the usual T-s plots and asks that every problem start with one. The ideal Rankine cycle at 15 MPa is shown to leave the low-pressure turbine at only 80% quality, which is too wet, so reheat is added. Part B adds regeneration: an open feedwater heater that mixes bled steam with condensate, a closed one that uses a heat exchanger, and a combination of both. Mass fractions of bled steam are found from an energy balance. The chapter closes with a case study of the 2.6 GW Gavin power plant.
Key Points:
- Plot the whole cycle on a P-h diagram first; constant-entropy lines show the path of an isentropic turbine
- Aim for quality above about 90% at the last turbine stage; wet steam erodes blades, as it did on the Gavin low-pressure turbines
- Reheat expands the steam in a high-pressure turbine, reheats it, and finishes in a low-pressure turbine, which improves exit quality
- An open feedwater heater mixes bled steam with compressed liquid and also works as a de-aerator
- A closed feedwater heater passes bled steam through a heat exchanger, so the two streams stay at different pressures
- Regeneration raises thermal efficiency slightly but lowers net work per kilogram of steam, because some steam bypasses the later turbine stages
- In the Gavin case study, a separate turbine drives the feedwater pump, which lifts the pressure to 30 MPa before pipe losses bring it to 25 MPa at the turbine inlet
Memory Tip: Bled steam is steam that gives up turbine work to heat the water for free. Efficiency goes up because the boiler has less heating to do, and work per kilogram goes down.
Common Mistake: Forgetting the bleed fraction y. After the heater the flow through the downstream turbine is (1 − y) of the boiler flow, so turbine work and heat terms must be weighted by the right fractions.
Important Questions:
- Why is reheat used in a steam power cycle? At high boiler pressure a single expansion would leave the steam too wet. Reheating partway restores temperature, keeps the exit quality high enough to protect the blades, and increases the work output.
- What does an open feedwater heater do? It mixes steam bled from the turbine with compressed liquid to preheat the feedwater, which lifts efficiency a little and also removes dissolved gases as a de-aerator.
Chapter 9: Carbon Dioxide (R744) – The New Refrigerant
Part 2: Applied Engineering Thermodynamics · Difficulty: Medium · one prediction has dated · Key topics: R744, global warming potential, CO2 property tables, P-h and h-s diagrams, transcritical cycle, heat pump, geothermal heat pump
This chapter picks up the CO2 refrigerant story begun in Chapter 4, Part D, and the opening discussion is largely the same. It retells the history: ammonia and CO2 first, then Freon 12 (banned because of ozone damage), then R134a with a global warming potential of 1300. The author argues that CO2’s old drawbacks, high pressure and a very hot compressor outlet, are now advantages. Because he found no published tables for R744, he built his own from NIST software (Appendix K), with a P-h and an h-s diagram. A CO2 heat-pump cycle is analysed, ending with a home geothermal heat-pump problem.
Key Points:
- Global warming potential (GWP) is measured against CO2, which has GWP = 1; R134a has about 1300
- CO2 cycles operate at roughly 30 to 200 atmospheres and with a compressor outlet near 160°C, which makes them transcritical
- High operating pressure means high fluid density, so equipment can be made smaller for the same heat-pumping power
- The hot outlet suits combined space heating and hot-water heating in homes
- Property tables for R744 (Appendix K) and its P-h and h-s diagrams are used the same way as for water and R134a
- Dated: the car air conditioning argument has not played out as predicted (most new cars use R1234yf); R744 is established mainly in commercial refrigeration and some heat pumps
Memory Tip: Same four components as the R134a cycle, but the high-pressure side does not condense; it just cools as a supercritical gas, which is why the outlet stays so hot.
Common Mistake: Looking for a saturated-liquid state at the high-pressure side of a CO2 cycle. Above the critical pressure there is no condensation, so you must use the superheat or transcritical table.
Important Questions:
- Why did the author argue for CO2 as a refrigerant? It has a GWP of 1, and its high pressure and high discharge temperature allow compact systems and useful heating for hot water or windshield defrosting.
- What does a GWP of 1300 mean? A kilogram of R134a leaked into the air traps about 1300 times as much heat over the reference period as a kilogram of CO2.
Chapter 10: Air – Water Vapor Mixtures (Parts A to C)
Part 2: Applied Engineering Thermodynamics · Difficulty: Medium · Key topics: Dalton’s law, specific humidity, relative humidity, adiabatic saturation, wet-bulb temperature, psychrometric chart, air conditioning processes, cooling tower, makeup water
Part A treats atmospheric air as dry air plus water vapor. Using Dalton’s law and the ideal gas model for low temperatures, it defines specific humidity (vapor mass per mass of dry air) and relative humidity (partial pressure over saturation pressure). Since neither can be measured directly, the adiabatic saturation process leads to the wet and dry bulb (sling) psychrometer. Part B introduces the psychrometric chart, including a simplified chart plotted from the equations, and uses it for heating, cooling and humidification problems. Part C applies mass and enthalpy balances to a cooling tower for the steam power plant, finding the dry-air flow and the makeup water.
Key Points:
- Dalton’s law: the pressure of the mixture is the dry-air pressure plus the vapor pressure
- Specific humidity ω is always based on the mass of dry air, not on the whole mixture
- Relative humidity φ = Pv/Pg, the vapor pressure compared with saturation pressure at the same temperature
- The wet-bulb temperature is very close to the adiabatic saturation temperature, so a wet and dry bulb pair gives humidity
- The psychrometric chart puts all these variables on one plot and makes air-conditioning processes quick to follow
- Cooling tower: makeup water equals the humidity gain of the air times the dry-air flow, and an enthalpy balance links air flow to circulating water
Memory Tip: Specific humidity is how much water the air carries (per kg of dry air); relative humidity is how full the air is compared with what it could hold at that temperature.
Common Mistake: Basing mass flows on the total moist air instead of the dry air. The book always takes the dry-air flow as the reference because it does not change through the process.
Important Questions:
- Why is the wet-bulb temperature useful? It is a simple measurement that nearly equals the adiabatic saturation temperature, which, together with the dry-bulb temperature, fixes the humidity of the air.
- Why does a steam plant use a cooling tower? The condenser rejects a huge amount of heat to cooling water; if no river can supply that flow, a tower cools the circulating water by evaporating part of it, which is why makeup water is needed.
Chapter 11: Combustion
Part 2: Applied Engineering Thermodynamics · Difficulty: Medium · Key topics: air composition, stoichiometric combustion, theoretical air, air-fuel ratio, excess air, dry product analysis, dew point, enthalpy of combustion, adiabatic flame temperature
The last chapter explains where the heat in earlier problems comes from. It limits itself to generic hydrocarbon fuels burning in atmospheric air, taken as 21% oxygen and 79% nitrogen, so every mole of O2 brings 3.76 moles of N2. Stoichiometric combustion is solved by balancing C, H, O and N atoms, then extended to theoretical air, air-fuel ratio, excess air and the volumetric analysis of products, including dew point. The First Law is then applied to reacting mixtures using a 25°C, 1 atm reference state, which leads to the adiabatic flame temperature. Solid fuels and complex fuel blends such as gasoline are outside its scope.
Key Points:
- Air is modelled as 21% O2 and 79% N2 by volume, molar mass about 29 kg/kmol, and nitrogen is assumed not to react
- Stoichiometric combustion leaves no oxygen in the products; atom balances for C, H, O and N give the coefficients
- Excess air raises the air-fuel ratio above the theoretical value and leaves O2 in the products
- Partial pressures and volume fractions of products give the dew point of the water in the exhaust
- First Law for reacting systems compares the enthalpies of products and reactants (kJ/kmol) from a common 25°C, 1 atm reference
- The adiabatic flame temperature is the highest temperature the products can reach when no heat leaves
Memory Tip: Every O2 you add to a combustion equation arrives with 3.76 N2. Write them together as one air package and the nitrogen balance takes care of itself.
Common Mistake: Leaving nitrogen out of the products. It does not react, but it still carries heat and dilutes the exhaust, so leaving it out gives a wrong dew point and flame temperature.
Important Questions:
- How many moles of nitrogen accompany each mole of oxygen in air? 79/21 = 3.76 moles of N2, which is why air is written as O2 + 3.76 N2.
- What is the adiabatic flame temperature? The temperature products reach when a fuel burns completely with no heat loss and no work, so the whole enthalpy released heats the products.
Appendices A to O
Appendix · Difficulty: Medium (reference tables plus several derivations) · Key topics: steam tables, R134a and CO2 tables, Lee-Kesler chart, ideal gas data, entropy summary sheets, Stirling-Carnot paper, psychrometric chart, combustion enthalpy tables
The appendices fill roughly a quarter of the book and are mostly reference tables. Appendix A holds steam tables from the NIST Chemistry WebBook (accessed January 2008) in seven parts, from temperature and pressure saturation tables to superheated, compressed-liquid data and an h-s diagram. C to G give critical properties, the Lee-Kesler compressibility chart, CO2 superheat tables, ideal-gas data at 300 K and specific heats of air. J and K add R134a and CO2 tables. Several appendices are real reading: B is a power-plant tour, H a fictional Stirling-Carnot meeting, I the adiabatic ideal gas process, L the entropy derivations and summary sheets, M a MATLAB psychrometric chart, O combustion enthalpies.
Key Points:
- Appendix A.1 to A.6 cover saturation, superheated and compressed-liquid steam; A.7 is the h-s diagram used for turbines
- The steam tables use critical values of 22.064 MPa and 373.95°C, with R = 0.4615 kJ/kg.K and a liquid specific heat of 4.18 kJ/kg.°C
- Appendix L derives entropy from the Clausius inequality and ends with three summary sheets: entropy equations, isentropic processes and adiabatic efficiency
- Appendix H argues that the ideal Stirling engine should be taught beside the Carnot cycle, since both share the same ideal efficiency
- Appendix I derives the adiabatic ideal-gas relations directly from the energy equation, which is why they appear before entropy in Chapter 3
- Appendix M gives a MATLAB program for plotting a simplified psychrometric chart
Common Mistake: Interpolating between table rows without checking units and region. Pressure is in kPa in some tables and MPa in others, and a state in the quality region must come from the saturation tables, not from the superheat table.
Important Questions:
- Which appendix do you use for a turbine problem on steam? Appendix A: the saturation and superheat tables for state properties, and A.7, the h-s diagram, to plot and check the expansion.
- Where are the entropy equations collected? In Appendix L, which has the Entropy Equation Summary Sheet, the Isentropic Process Summary Sheet and the Adiabatic Efficiency Summary Sheet.
How to Study This Book
The author designed this text as a self-contained two-course sequence for mechanical engineers. Part 1 (Chapters 1 to 6) is the first course: the First and Second Laws, applied to whole cycles rather than to isolated components. Part 2 (Chapters 7 to 11) is the second course: exergy, advanced steam cycles, CO2 refrigeration, air-water mixtures and combustion. If your syllabus is split into Thermodynamics I and II, that is a natural cut, and the chapter headings carry lettered sections (for example 3a to 3d) so you can read in small pieces.
Start with Chapter 1 even if it looks easy. Its definitions (closed system, control volume, state postulate, absolute pressure) and the habit of drawing a labelled sketch before calculating are used in every later chapter. In Chapter 2, spend time on quality and on sketching T-v and P-v diagrams, because Chapters 3 and 4 depend on them. Chapter 3 is long; if time is short, read 3a (energy equation, Cv, Cp) and then either the Diesel and Otto sections (3c, 3d) for an engines course or the Stirling section (3b) for a heat-engine course.
Chapter 4 is the heart of Part 1. Learn the steady-flow energy equation in 4a and then work through the steam plant in 4b and the refrigerator in 4c; every later chapter reuses those component-by-component calculations. Chapters 5 and 6 need a fresh mind. Read Chapter 5 for the two Second Law statements and reversibility, then use Appendix L together with Chapter 6, because the entropy derivations and the three summary sheets live there rather than in the chapter itself.
In Part 2, Chapter 7 (exergy) is the hardest chapter, so read the wind and hydro examples first to build the idea. Chapter 8 returns to the steam plant, so keep your Chapter 4 work next to it. Chapter 9 repeats the introduction of Chapter 4, Part D; if you have already read that part, go straight to the property tables and the CO2 heat-pump cycle. The car air conditioning forecast in Chapters 4d and 9 has not played out as the book expected (most new cars use R1234yf), so read it as a case study, not as current industry fact. Chapter 10 (psychrometrics) and Chapter 11 (combustion) are largely independent of each other and can be read in either order.
Keep the Appendix A steam tables, Appendix J (R134a), Appendix K (CO2) and Appendix L open while you work. The steam data comes from the NIST Chemistry WebBook as accessed in January 2008, which is fine for coursework, but if your lecturer supplies a different table set, use that one in exams. The book is text and figures only: the animations, videos and online tools it mentions are links to outside web pages and are not inside the PDF.
Know what the book does not do. It has no chapters on thermodynamic property relations such as the Maxwell relations, on chemical equilibrium, or on gas mixtures other than air and water vapor and combustion products, and it treats only steady-flow control volumes. It also has no separate answer key; many numbered problems print their final answers in square brackets right after the question. Work each problem blind first and compare afterwards.
Used In These Programs
This book is used for the Thermodynamics course in: BS Mechanical Engineering · BS Chemical Engineering. Browse all Thermodynamics books or all Engineering category books.
Who Should Read This
Engineering Thermodynamics: A Graphical Approach is written for BS Mechanical Engineering students and suits BS Chemical Engineering students who need the same First Law, Second Law, steam cycle, refrigeration and combustion toolkit. It works best for learners who want to see a power plant or a refrigerator as a picture on a P-h or h-s diagram before using equations, and for self-study, because every solved problem follows the same sketch, tables and equations routine. Calculus is used in the derivations, so you should be comfortable with integration and partial derivatives. If your first exposure to heat and temperature was in physics, University Physics Volume 2 covers temperature, kinetic theory and the two laws at a lighter level and is a good warm-up. It is not a book for students who want a property-relations or chemical-equilibrium course.
Applicable Universities
This book is useful for students at Pakistani universities offering BS Mechanical Engineering or BS Chemical Engineering, including UET Lahore, NUST, GIKI, COMSATS, NED, FAST, Punjab University, and other HEC-recognized and PEC-accredited institutions, wherever a two-course sequence in engineering thermodynamics is part of the degree.
Official Copy of Engineering Thermodynamics: A Graphical Approach
This book is free from its official source, the OHIO Open Library. Click the button below to open the official page, where you can download the complete PDF (Download Full Text) and the separate properties tables booklet.
→ Visit Official PageFAQs
Is Engineering Thermodynamics: A Graphical Approach free?
Yes. The book’s own copyright page says it is licensed under the Creative Commons Attribution-NonCommercial-ShareAlike 3.0 United States licence (CC BY-NC-SA 3.0 US), so you may read, download and share it for non-commercial use with credit. The OHIO Open Library record now lists the same work under the 4.0 International version of that licence.
Which edition is this, and is it still current?
It is the 2021 edition in the OHIO Open Faculty Textbooks series, a text version of the author’s earlier web resource. The core thermodynamics has not aged, but two things have: the steam data comes from the NIST Chemistry WebBook as accessed in January 2008, and the book expects CO2 to replace R134a in car air conditioning, which has not happened because most new cars moved to another refrigerant (R1234yf).
Does the PDF include steam tables and the web tools?
The PDF includes the property tables you need: steam tables (Appendix A), R134a (Appendix J), CO2 (Appendix K), critical data, the Lee-Kesler chart and specific heats. It does not include the original web resource’s animations, videos or outside links. The official page also offers a separate properties tables booklet as an extra download.
Does it include solved exercises?
Yes. Most chapters work through solved problems step by step, usually with a labelled sketch, a property diagram and the tables. Many further numbered problems print their final answers in square brackets. There is no separate answer key and no end-of-chapter problem sets in the usual textbook sense.
Is it a good book for a first thermodynamics course?
It can be, if you are comfortable with calculus and like learning from diagrams and complete cycles. It builds from definitions in Chapter 1 and is clear about method, but entropy only arrives in Chapter 6, and it has no chapters on property relations such as the Maxwell relations or on chemical equilibrium. Use it beside your lecturer’s syllabus.
Does it cover the Rankine cycle, refrigeration and the Otto and Diesel cycles?
Yes. Chapter 3 covers the Stirling, Diesel and Otto cycles, Chapter 4 steam plants and R134a refrigeration and heat pumps, Chapter 8 the ideal Rankine, reheat and regenerative cycles, and Chapter 6 aircraft gas turbine engines. Chapters 10 and 11 add psychrometrics, cooling towers and combustion.
Related Books
- University Physics Volume 2 – temperature, kinetic theory, and the first and second laws at physics level
- University Physics Volume 1 – the work, energy, and mechanics background behind Chapter 1
- Calculus Volume 3 – multivariable calculus and the partial derivatives used for specific heats
- Calculus Volume 1 – the integration behind boundary work and entropy
Engineering Thermodynamics: A Graphical Approach gives you a free, diagram-first route from units and steam tables to power plants, refrigeration, exergy and combustion. Browse more Engineering books for the rest of your semester.
Engineering Thermodynamics – A Graphical Approach by Israel Urieli, Ohio University. OHIO Open Faculty Textbooks, 2021. Copyright 2021 Israel Urieli, licensed under the Creative Commons Attribution-NonCommercial-ShareAlike 3.0 United States licence (CC BY-NC-SA 3.0 US). Official source: https://ohioopen.library.ohio.edu/opentextbooks/8/
© Copyright Policy
Freebooks.pk is an educational resource for students in Pakistan. Textbooks and other books belong to their respective boards, authors and publishers, and all rights remain with them. If you are the copyright holder of any material on this page and want it changed or removed, please contact us or file a request under our DMCA policy. We review every request and remove reported content promptly.
